起订:1台
发货:2天内
发送询价
体积电阻率表面电阻率测试仪数字超高阻、微电流测量仪 型号：EST-121：体积电阻率,表面电阻率 用途：仪器仪表检测试验一、体积电阻率表面电阻率测定仪概述本仪器是既可测量高电阻，又可测微电流。采用了美国Intel公司的大规模集成电路以及专利技术,使仪器体积小、重量轻、准确度高。以双3.1/2 位数字直接显示电阻的高阻计和电流。量限从1×104Ω ～1×1018 Ω，是目前国内测量范围*宽，准确度*高的数字超高阻测量仪。电流测量范围为2×10-4 ～1×10-16Ａ。机内测试电压为10/50/100/250/500/1000V任意可调。本仪器具有精度高、显示迅速、性好稳定、读数方便， 适用于防静电产品如防静电鞋、防静电塑料橡胶制品、计算机房防静电活动地板等电阻值的检验以及绝缘材料和电子电器产品的绝缘电阻测量。本仪器除能测电阻外，还能直接测量微弱电流。仪完全符合并优于国家标准GB1410《固体电工绝缘材料绝缘电阻、体积电阻系数和表面电阻试验方法》和美国标准ASTM D257《绝缘材料的直流电阻或电导试验方法》等标准的要求。二、体积电阻率表面电阻率测试仪主要特点电阻测量范围宽 0.01×104Ω ～1×1018 Ω电流测量范围为 2×10-4Ａ ～1×10-16Ａ体积小、重量轻、准确度高电阻、电流双显示性能好稳定、读数方便所有测试电压(10/50/100/250/500/1000V) 测试时电阻结果直读，免去老式高阻计在不同测试电压下或不同量程时要乘以系数等使用不便的麻烦， 使测量超高电阻就如用万用表测量普通电阻样简便。既能测超高电阻又能测微电流适用范围广:适用于防静电产品如防静电鞋、防静电塑料橡胶制品、计算机房防静电活动地板等电阻值的检验和电子电器产品的绝缘电阻测量三、体积电阻率表面电阻率测试仪技术指标1.电阻测量范围： 0.01×104Ω ～1×1018Ω。2.电流测量范围为: 2×10-4A～1×10-16A3. 双表头显示: 3.1/2位LED显示4. 内置测试电压： 10V、50V、100V、250、500、1000V5. 基本准确度：1% (*注)6 使用环境: 温度：0℃～40℃，相对湿度<80%7 机内测试电压: 10/50/100/250/500/1000V 任意切换8.供电形式: AC 220V，50HZ，功耗约5W四、体积电阻率表面电阻率测试仪工作原理根据欧姆定律，被测电阻Rx等于施加电压V除以通过的电流I。传统的高阻计的工作原理是测量电压V固定，通过测量流过取样电阻的电流I来得到电阻值。从欧姆定律可以看出，由于电流I是与电阻成反比，而不是成正比，所以电阻的显示值是非线性的，即电阻无穷大时，电流为零，即表头的零位处是∞，其附近的刻度非常密，分辨率很低。整个刻度是非线性的。又由于测量不同的电阻时，其电压V也会有些变化，所以普通的高阻计是精度差、分辨率低。同时测出电阻两端的电压V和流过电阻的电流I，通过内部的大规模集成电路完成电压除以电流的计算，然后把所得到的结果经过A/D转换后以数字显示出电阻值，即便是电阻两端的电压V和流过电阻的电流I是同时变化，其显示的电阻值不象普通高阻计那样因被测电压V的变化或电流Ｉ的变化而变，所以，即使测量电压、被测量电阻、电源电压等发生变化对其结果影响不大，其测量精度很高(专利)，从理论上讲其误差可以做到零，而实际误差可以做到千分之几或万分之几。典型应用1．测量防静电鞋、导电鞋的电阻值2、测量防静电材料的电阻及电阻率3、测量计算机房用活动地板的系统电阻值4、测量绝缘材料电阻(率)5、光电二极管暗电流测量6、物理,光学和材料研究标准配置：1.测试仪器：1台2.电源线：1条3.测量线：3根(屏蔽线、测试接线、接地线)4.使用说明书：1份其它可选配件：本仪器配不同的测量电极(夹具)可以测量不同材料不(固体、粉体或液体)的体积电阻率和表面电阻率或电导率，完全符合或优于国家标准GB1410－89固体电工绝缘材料绝缘电阻、体积电阻系数和表面电阻试验方法，ASTM D257 绝缘材料的直流电阻或电导试验方法等标准要求。表面电阻和体积电阻测试电极(三电极) 屏蔽箱 北广公司其它绝缘材料检测仪器: BDJC-0-100KV 介**穿试验仪BDJC系列绝缘材料工频率介**穿试验仪BDJC系列电压介电强度试验仪器BDJC系列 电压击穿试验仪 BDJC系列绝缘漆漆膜击穿强度试验仪BDJC电容器纸工频电压击穿试验仪EST-121 体积表面电阻率测定仪 GDAT-A介质损耗测试仪/介电常数测试仪 GDAT-C新型介电常数介质损耗测试仪BDH 耐漏电起痕试验仪BDH-B耐电弧试验仪中国检测行业与验证服务的尖端者和智领者，帮助众多检测质检单位和学校教研单位提供一站式的全面质量解决方案。注重每一个细节是北广公司对于每个客户的承诺 ， 也是北广公司一直追求的宗旨。北京北广精仪仪器设备有限公司 www.beiguangjy.comVolume resistivity of surface resistivity testerDigital high resistance, a current measuring instrument type: EST-121: volume resistivity, surface resistivity uses: Instrumentation TestOne, volume resistivity surface resistivity tester overviewThis instrument can measure high resistance, and measuring current. The American company Intel large scale integrated circuit and patented technology, the instrument has the advantages of small volume, light weight, high accuracy. Dual 3.1/2 digital display the resistance high resistance meter and current. Limit from 1× 104 Ω～ 1× 1018 Ω, is currently the most wide measurement range, the most accurate digital ultra high resistance meter. Current measurement range of 2× 10-4 ～ 1× 10-16A. The built-in test voltage is 10/50/100/250/500/1000V adjustable. The instrument has the advantages of high pcision, good stability, showing a rapid, easy reading, applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as the resistance value of the test as well as insulating materials electrical and electronic products insulation resistance measurement. The instrument can measure the resistance, and can directly measure the weak current. Instrument is fully consistent with and better than the national standard GB1410 " solid electrical insulating materials, insulation resistance, volume resistivity and surface resistance test method " and " American Standard ASTM D257 DC resistanceorconductance of insulating materials test methods " and other standards.Two, volume resistivity surface resistivity tester main featuresResistance measuring range 0.01× 104 Ω～ 1× 1018 ΩCurrent measurement range of 2× 10-4A ～ 1× 10-16ASmall volume, light weight, high accuracyResistance, current double displayGood performance is stable, easy readingAll the test voltage ( 10/50/100/250/500/1000V ) test resistance results in reading, is removed from the old high resistance meter in different test voltageordifferent scale should be multiplied by the coefficient of the inconvenient trouble, allowing the measurement of high resistance as the multimeter is used to measure the general resistance of samples is simple.Not only can measure high resistance and micro currentWide application: applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as resistance testing electrical and electronic products insulation resistance measurementThree, volume resistivity surface resistivity tester technical indicatorsThe 1 resistor measurement range: 0.01× 104 Ω～ 1× 1018 Ω.The 2 current measurement range : 2 × 10-4A～ 1 × 10-16A3 double header display: 3.1/2 LED display4 built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V5 basic accuracy: 1% ( note )6: use environment temperature: 0℃ 40 ℃, relative humidity <80%7 built-in test voltage: 10/50/100/250/500/1000V arbitrary switchingThe 8 power supply forms: AC 220V, 50HZ, power consumption is about 5WFour, volume resistivity surface resistivity meter working principleAccording to the Ohm's law, the measured resistance is equal to voltage is applied through Rx V divided by the current I. The traditional high resistance meter is the working principle of measuring voltage V fixed, by measuring the current flows through the sampling resistor I to get the value of resistance. From Ohm's law can be seen, because the current I is inversely proportional to the resistance, but not proportional to the resistance, so the display value is nonlinear, namely the resistance to infinity, the current is zero, i.e., zero is∞, in the vicinity of the scale is very dense, with a low resolution. The scale is nonlinear. Because the measurement of different resistance, the voltage V also vary, so the average high resistance meter is poor accuracy, low resolution.At the same time measure the voltage across the resistor V and the current through the resistor I, through the interior of the large scale integrated circuit to complete the voltage divided by the current calculation, and then the results obtained after A/D conversion to digital show resistance, even if the voltage across the resistor V and the current through the resistor I is changed at the same time, the display resistance value is not as common due to high resistance meter that measured voltageorcurrent change of V I change, so, even if the measured voltage, resistance, power supply voltage is measured the changes in the results have little effect, the measurement accuracy is very high ( patent ), theoretically the error can be zero, while the actual error can be done a few thousandthsorextremely few.Typical application1 measurements of anti-static shoes, conductive shoes resistance value2, measurement of the antistatic material resistance and resistivity3, measurement computer room with movable floor system resistance4, measurement of insulation resistance ( rate)5, photodiode dark current measurement6, physics, optics and materials researchCanton company other insulating materials testing instruments:BDJC-0-100KV dielectric breakdown testing instrumentBDJC series insulating materials at power frequencies of dielectric breakdown test instrumentBDJC series voltage dielectric strength test apparatusBDJC series voltage breakdown testing instrumentBDJC series insulating paint film breakdown strength testerBDJC capacitor voltage breakdown testing instrumentEST-121 volume surface resistivity measuring instrumentGDAT-A dielectric loss tester / dielectric constant testGDAT-C model dielectric constant dielectric loss testerBDH leakage resistance testerBDH-B arc resistance testerChina Inspection and certification services tip and intellectual leader, helped many testing quality inspection units and schools and research units to provide comphensive one-stop quality solutions.Pay attention to every detail is Canton company for each customer commitment, and North Canton company has been pursuing the aim of. Beijing North Canton pcision instrument equipment limited www.beiguangjy.com